Shaft repair sleeves · Inch & metric

Speedi Sleeve Size Chart

An SKF Speedi-Sleeve is a thin stainless steel sleeve that slides over a worn seal track and gives the lip seal a new running surface. The wall is only 0.011 in (0.28 mm) thick, so you can fit a new seal of the original size without machining the shaft. Measure the shaft next to the worn band and the finder shows every size that fits, with live price and stock. Prefer to browse? Use the full size chart or shop all SKF Speedi-Sleeves.

336

SKF Speedi-Sleeve sizes in the chart
0.472–8 in

Shaft diameters covered (12–203 mm)
0.011 in

Thin wall: keep your original seal size
2 types

Standard, or Gold-coated for abrasive duty

Size finder

Find your SKF Speedi-Sleeve

How do you want to find your sleeve?

How to measure (30 s)

Use a micrometer and read to 0.001 in (0.01 mm) or finer. Each size fits a shaft range only 0.002–0.010 in (0.05–0.25 mm) wide.
Measure next to the worn band, on the smooth shaft where the sleeve will sit, not in the groove.
Take three readings about 60° apart and enter all three. If they disagree, the finder asks you to re-measure.

Full measuring guide

.sss-finder .sss-quote[hidden] { display: block !important; } .sss-finder .sss-entry, .sss-finder .sss-entry__label, .sss-finder .sss-boot { display: none !important; }

The size finder needs JavaScript. You can still browse all SKF Speedi-Sleeves, find your size in the size chart, or send us your shaft readings with the form below and we'll pick the right part for you.

Unit

Inches Millimetres

Shaft diameter readings

Measure the smooth, unworn part of the shaft where the sleeve will sit, in three places about 60° apart. Use a micrometer: each size fits a shaft range only 0.002–0.010 in (0.05–0.25 mm) wide.

Reading 1 (required)

Reading 2

Reading 3

Sizes come from SKF's published catalogue data. Check your readings before you install: a Speedi-Sleeve can't be removed and used again.

Measuring guide

How to measure your shaft for a Speedi-Sleeve

A Speedi-Sleeve is sized to your shaft's original diameter, not to the worn groove. Each size fits a very narrow range, so a few careful readings with a micrometer matter more than anything else. Once you have them, enter them in the size finder or look them up in the size chart.

Measure the smooth, unworn shaft right next to the worn band, three times around, and note where the band starts and ends.

Tip

Calipers aren't precise enough. Each Speedi-Sleeve size covers a shaft range only 0.002 to 0.010 in (0.05 to 0.25 mm) wide: too narrow to judge with a caliper. Use an outside micrometer that reads to 0.001 in (0.01 mm) or finer.

Clean the shaft
Wipe off oil, grease and dirt. File or stone away burrs, nicks and raised edges so they don't throw off your readings.
Find the unworn section next to the worn band
The seal lip leaves a polished track or groove on the shaft: the worn band. Measure on the smooth, unworn metal right next to it, where the sleeve will sit. Never measure in the groove itself.
Take three readings with a micrometer
Measure the diameter at three positions about 60° apart around the shaft. Three readings show up a shaft that is out of round, and one bad reading won't decide the size.
Average the readings
Add the three readings together and divide by three. Pick a sleeve whose shaft range includes the average: for example, SKF 99868 fits 0.998–1.002 in. If your readings are far apart, clean the shaft and measure again.
Note where the worn band starts and ends
Measure from the shaft end to the near edge and to the far edge of the worn band. Include the dust-lip track and any end float, so the sleeve covers every surface the seal can touch. These two distances tell you which sleeve width you need.
Check for anything in the way
A Speedi-Sleeve can't go over a keyway, spline, cross hole or thread, so check the area it will cover. Also note any part that stays on the shaft, such as a bearing, shoulder or collar, and how far it is from the shaft end.

Full size chart

SKF Speedi-Sleeve size chart

Every SKF Speedi-Sleeve size, sorted by shaft diameter, in inches and millimetres. Open the band for your shaft, then pick a part whose range includes the average of your readings and whose width covers the whole worn band. Parts we list online link to their product page with live price and stock. Would rather not do the matching yourself? Enter your readings in the size finder.

Under 1 in (under 25.4 mm) 30 sizes

SKF Speedi-Sleeves for shafts under 1 in (under 25.4 mm)
Part no.	Type	Fits shaft (in)	Fits shaft (mm)	Covers in (mm)	Total width in (mm)	Flange OD in (mm)	Max install depth in (mm)	Action
SKF 99049	Standard	0.472–0.475^†	11.99–12.07^†	0.236 (5.99)	0.331 (8.41)	0.610 (15.49)	1.875 (47.63)
SKF 99050	Standard	0.498–0.502	12.65–12.75	0.250 (6.35)	0.344 (8.74)	0.610 (15.49)	2.000 (50.80)
SKF 99055	Standard	0.547–0.551	13.89–14.00	0.250 (6.35)	0.391 (9.93)	0.750 (19.05)	1.831 (46.51)
SKF 99056	Standard	0.560–0.566^†	14.22–14.38^†	0.250 (6.35)	0.391 (9.93)	0.750 (19.05)	1.831 (46.51)
SKF 99059	Standard	0.589–0.593	14.96–15.06	0.197 (5.00)	0.354 (8.99)	0.750 (19.05)	1.862 (47.29)
SKF 99062	Standard	0.623–0.627	15.82–15.93	0.313 (7.95)	0.406 (10.31)	0.750 (19.05)	2.000 (50.80)
SKF 99810	Gold	0.623–0.627	15.82–15.93	0.313 (7.95)	0.406 (10.31)	0.750 (19.05)	2.000 (50.80)
SKF 99058	Standard	0.626–0.630	15.90–16.00	0.313 (7.95)	0.438 (11.13)	0.718 (18.24)	2.000 (50.80)
SKF 99068	Standard	0.667–0.671	16.94–17.04	0.315 (8.00)	0.433 (11.00)	0.875 (22.23)	2.000 (50.80)
SKF 99060	Standard	0.682–0.686	17.32–17.42	0.313 (7.95)	0.438 (11.13)	0.900 (22.86)	2.000 (50.80)
SKF 99082	Standard	0.704–0.709^†	17.88–18.01^†	0.315 (8.00)	0.433 (11.00)	0.962 (24.43)	1.811 (46.00)
SKF 99076	Standard	0.748–0.752	19.00–19.10	0.313 (7.95)	0.438 (11.13)	0.945 (24.00)	2.000 (50.80)
SKF 99811	Gold	0.748–0.752	19.00–19.10	0.313 (7.95)	0.438 (11.13)	0.945 (24.00)	2.000 (50.80)
SKF 99081	Standard	0.759–0.761^†	19.28–19.33^†	0.313 (7.95)	0.438 (11.13)	0.938 (23.83)	2.000 (50.80)
SKF 99080	Standard	0.780–0.784	19.81–19.91	0.313 (7.95)	0.438 (11.13)	0.935 (23.75)	2.000 (50.80)
SKF 99075	Standard	0.782–0.786^‡	19.86–19.96^‡	0.339 (8.60)	0.437 (11.10)	0.930 (23.60)	1.875 (47.60)	Quote
SKF 99078	Standard	0.785–0.789	19.94–20.04	0.315 (8.00)	0.433 (11.00)	0.930 (23.62)	2.000 (50.80)
SKF 99083	Standard	0.812–0.815^†	20.62–20.70^†	0.375 (9.53)	0.563 (14.30)	1.188 (30.18)	3.000 (76.20)
SKF 99086	Standard	0.857–0.861	21.77–21.87	0.250 (6.35)	0.375 (9.53)	1.155 (29.34)	2.000 (50.80)
SKF 99084	Standard	0.861–0.866^†	21.87–22.00^†	0.259 (6.58)	0.359 (9.12)	1.188 (30.18)	1.856 (47.14)
SKF 99085	Standard	0.861–0.866^†	21.87–22.00^†	0.315 (8.00)	0.472 (11.99)	1.188 (30.18)	1.812 (46.02)
SKF 99087	Standard	0.873–0.877	22.17–22.28	0.313 (7.95)	0.438 (11.13)	1.094 (27.79)	2.000 (50.80)
SKF 99812	Gold	0.873–0.877	22.17–22.28	0.313 (7.95)	0.438 (11.13)	1.094 (27.79)	2.000 (50.80)
SKF 99091	Standard	0.908–0.912	23.06–23.16	0.313 (7.95)	0.438 (11.13)	1.218 (30.94)	1.847 (46.91)
SKF 99860	Gold	0.908–0.912	23.06–23.16	0.313 (7.95)	0.438 (11.13)	1.218 (30.94)	1.847 (46.91)
SKF 99092	Standard	0.940–0.945^†	23.88–24.00^†	0.313 (7.95)	0.438 (11.13)	1.130 (28.70)	2.000 (50.80)
SKF 99094	Standard	0.966–0.970	24.54–24.64	0.313 (7.95)	0.438 (11.13)	1.130 (28.70)	2.000 (50.80)
SKF 99096	Standard	0.966–0.970	24.54–24.64	0.625 (15.88)	0.719 (18.26)	1.130 (28.70)	2.000 (50.80)
SKF 99098	Standard	0.982–0.986	24.94–25.04	0.313 (7.95)	0.433 (11.00)	1.300 (33.02)	2.000 (50.80)
SKF 99813	Gold	0.982–0.986	24.94–25.04	0.313 (7.95)	0.433 (11.00)	1.300 (33.02)	2.000 (50.80)

1.000–1.999 in (25.4–50.8 mm) 90 sizes

SKF Speedi-Sleeves for 1.000–1.999 in (25.4–50.8 mm) shafts
Part no.	Type	Fits shaft (in)	Fits shaft (mm)	Covers in (mm)	Total width in (mm)	Flange OD in (mm)	Max install depth in (mm)	Action
SKF 99814	Gold	0.998–1.002^†	25.35–25.45^†	0.313 (7.95)	0.438 (11.13)	1.219 (30.96)	2.000 (50.80)
SKF 99868	Standard	0.998–1.002^†	25.35–25.45^†	0.313 (7.95)	0.438 (11.13)	1.219 (30.96)	2.000 (50.80)
SKF 99103	Standard	1.019–1.024	25.88–26.01	0.315 (8.00)	0.472 (11.99)	1.313 (33.35)	1.813 (46.05)
SKF 99106	Standard	1.060–1.064^†	26.92–27.03^†	0.313 (7.95)	0.438 (11.13)	1.320 (33.53)	1.843 (46.81)
SKF 99815	Gold	1.060–1.064^†	26.92–27.03^†	0.313 (7.95)	0.438 (11.13)	1.320 (33.53)	1.843 (46.81)
SKF 99108	Standard	1.087–1.091^†	27.61–27.71^†	0.313 (7.95)	0.438 (11.13)	1.406 (35.71)	0.625 (15.88)
SKF 99111	Standard	1.100–1.104^†	27.94–28.04^†	0.375 (9.53)	0.500 (12.70)	1.375 (34.93)	1.843 (46.81)
SKF 99866	Gold	1.100–1.104^†	27.94–28.04^†	0.375 (9.53)	0.500 (12.70)	1.375 (34.93)	1.843 (46.81)	Quote
SKF 99112	Standard	1.123–1.127^†	28.52–28.63^†	0.313 (7.95)	0.438 (11.13)	1.500 (38.10)	0.688 (17.48)
SKF 99116	Standard	1.123–1.127^†	28.52–28.63^†	0.375 (9.53)	0.500 (12.70)	1.500 (38.10)	0.688 (17.48)
SKF 99816	Gold	1.123–1.127^†	28.52–28.63^†	0.313 (7.95)	0.438 (11.13)	1.500 (38.10)	0.688 (17.48)
SKF 99120	Standard	1.154–1.158^†	29.31–29.41^†	0.375 (9.53)	0.500 (12.70)	1.350 (34.29)	0.688 (17.48)
SKF 99865	Gold	1.154–1.158^‡	29.31–29.41^‡	0.375 (9.53)	0.500 (12.70)	1.350 (34.29)	0.688 (17.48)	Quote
SKF 99122	Standard	1.173–1.178	29.79–29.92	0.313 (7.95)	0.438 (11.13)	1.400 (35.56)	0.688 (17.48)
SKF 99114	Standard	1.179–1.184	29.95–30.07	0.315 (8.00)	0.433 (11.00)	1.400 (35.56)	0.688 (17.48)
SKF 99118	Standard	1.185–1.190	30.10–30.23	0.313 (7.95)	0.438 (11.13)	1.400 (35.56)	0.688 (17.48)
SKF 99123	Standard	1.216–1.222^†	30.89–31.04^†	0.313 (7.95)	0.433 (11.00)	1.563 (39.70)	0.625 (15.88)
SKF 99141	Standard	1.237–1.243	31.42–31.57	0.315 (8.00)	0.438 (11.13)	1.540 (39.12)	0.688 (17.48)
SKF 99125	Standard	1.247–1.253	31.67–31.83	0.313 (7.95)	0.438 (11.13)	1.500 (38.10)	0.688 (17.48)
SKF 99817	Gold	1.247–1.253	31.67–31.83	0.313 (7.95)	0.438 (11.13)	1.500 (38.10)	0.688 (17.48)
SKF 99128	Standard	1.257–1.263	31.93–32.08	0.315 (8.00)	0.438 (11.13)	1.500 (38.10)	0.688 (17.48)
SKF 99876	Gold	1.257–1.263^‡	31.93–32.08^‡	0.315 (8.00)	0.437 (11.10)	1.500 (38.10)	0.688 (17.50)	Quote
SKF 99121	Standard	1.297–1.301^†	32.94–33.05^†	0.591 (15.01)	0.709 (18.01)	1.594 (40.49)	1.000 (25.40)	Quote
SKF 99129	Standard	1.308–1.314	33.22–33.38	0.250 (6.35)	0.375 (9.53)	1.600 (40.64)	0.813 (20.65)
SKF 99131	Standard	1.310–1.316	33.27–33.43	0.500 (12.70)	0.625 (15.88)	1.594 (40.49)	0.813 (20.65)
SKF 99818	Gold	1.310–1.316^‡	33.27–33.43^‡	0.500 (12.70)	0.625 (15.88)	1.594 (40.49)	0.813 (20.65)
SKF 99134	Standard	1.333–1.339	33.86–34.01	0.500 (12.70)	0.625 (15.88)	1.625 (41.28)	0.813 (20.65)
SKF 99133	Standard	1.371–1.377	34.82–34.98	0.313 (7.95)	0.438 (11.13)	1.638 (41.61)	0.813 (20.65)
SKF 99138	Standard	1.371–1.377	34.82–34.98	0.500 (12.70)	0.625 (15.88)	1.638 (41.61)	0.813 (20.65)
SKF 99819	Gold	1.371–1.377	34.82–34.98	0.500 (12.70)	0.625 (15.88)	1.638 (41.61)	0.813 (20.65)
SKF 99139	Standard	1.375–1.381	34.93–35.08	0.512 (13.00)	0.630 (16.00)	1.638 (41.61)	0.813 (20.65)
SKF 99820	Gold	1.375–1.381	34.93–35.08	0.512 (13.00)	0.630 (16.00)	1.638 (41.61)	0.813 (20.65)
SKF 99146	Standard	1.411–1.417	35.84–35.99	0.512 (13.00)	0.669 (16.99)	1.781 (45.24)	0.984 (24.99)
SKF 99143	Standard	1.432–1.438	36.37–36.53	0.563 (14.30)	0.688 (17.48)	1.781 (45.24)	1.016 (25.81)
SKF 99821	Gold	1.432–1.438	36.37–36.53	0.563 (14.30)	0.688 (17.48)	1.781 (45.24)	1.016 (25.81)
SKF 99144	Standard	1.435–1.441	36.45–36.60	0.375 (9.53)	0.500 (12.70)	1.781 (45.24)	1.016 (25.81)
SKF 99147	Standard	1.490–1.496	37.85–38.00	0.512 (13.00)	0.669 (16.99)	1.781 (45.24)	0.984 (24.99)
SKF 99149	Standard	1.497–1.503	38.02–38.18	0.563 (14.30)	0.688 (17.48)	1.781 (45.24)	1.016 (25.81)
SKF 99150	Standard	1.497–1.503	38.02–38.18	0.375 (9.53)	0.500 (12.70)	1.781 (45.24)	1.016 (25.81)
SKF 99822	Gold	1.497–1.503	38.02–38.18	0.563 (14.30)	0.688 (17.48)	1.781 (45.24)	1.016 (25.81)
SKF 99823	Gold	1.497–1.503	38.02–38.18	0.375 (9.53)	0.500 (12.70)	1.781 (45.24)	1.016 (25.81)
SKF 99152	Standard	1.520–1.526	38.61–38.76	0.438 (11.13)	0.563 (14.30)	1.859 (47.22)	1.016 (25.81)
SKF 99155	Standard	1.549–1.555	39.34–39.50	0.438 (11.13)	0.563 (14.30)	1.859 (47.22)	1.016 (25.81)
SKF 99156	Standard	1.559–1.565	39.60–39.75	0.563 (14.30)	0.688 (17.48)	1.859 (47.22)	1.016 (25.81)
SKF 99824	Gold	1.559–1.565	39.60–39.75	0.563 (14.30)	0.688 (17.48)	1.859 (47.22)	1.016 (25.81)
SKF 99159	Standard	1.566–1.572	39.78–39.93	0.625 (15.88)	0.750 (19.05)	1.859 (47.22)	1.016 (25.81)
SKF 99153	Standard	1.569–1.575^†	39.85–40.01^†	0.390 (9.91)	0.509 (12.93)	1.850 (46.99)	1.000 (25.40)
SKF 99157	Standard	1.572–1.578	39.93–40.08	0.512 (13.00)	0.630 (16.00)	1.850 (46.99)	1.023 (25.98)
SKF 99825	Gold	1.572–1.578^†	39.93–40.08^†	0.512 (13.00)	0.630 (16.00)	1.850 (46.99)	1.023 (25.98)
SKF 99160	Standard	1.602–1.608	40.69–40.84	0.500 (12.70)	0.641 (16.28)	1.938 (49.23)	1.000 (25.40)
SKF 99163	Standard	1.608–1.614	40.84–41.00	0.500 (12.70)	0.625 (15.88)	1.938 (49.23)	1.016 (25.81)
SKF 99161	Standard	1.622–1.628	41.20–41.35	0.313 (7.95)	0.438 (11.13)	1.875 (47.63)	1.016 (25.81)
SKF 99162	Standard	1.622–1.628	41.20–41.35	0.563 (14.30)	0.688 (17.48)	1.875 (47.63)	0.813 (20.65)
SKF 99826	Gold	1.622–1.628	41.20–41.35	0.563 (14.30)	0.688 (17.48)	1.875 (47.63)	0.813 (20.65)
SKF 99166	Standard	1.647–1.654^†	41.83–42.01^†	0.445 (11.30)	0.571 (14.50)	2.087 (53.01)	0.846 (21.49)
SKF 99169	Standard	1.647–1.654^†	41.83–42.01^†	0.563 (14.30)	0.689 (17.50)	2.087 (53.01)	0.827 (21.01)
SKF 99873	Gold	1.647–1.654^‡	41.83–42.01^‡	0.563 (14.30)	0.689 (17.50)	2.087 (53.01)	0.827 (21.01)	Quote
SKF 99165	Standard	1.653–1.659	41.99–42.14	0.550 (13.97)	0.689 (17.50)	2.087 (53.01)	0.827 (21.01)
SKF 99168	Standard	1.684–1.690	42.77–42.93	0.563 (14.30)	0.688 (17.48)	1.906 (48.41)	0.875 (22.23)
SKF 99167	Standard	1.685–1.691	42.80–42.95	0.313 (7.95)	0.438 (11.13)	1.906 (48.41)	0.875 (22.23)
SKF 99182	Standard	1.687–1.693	42.85–43.00	0.500 (12.70)	0.625 (15.88)	1.906 (48.41)	0.844 (21.44)
SKF 99171	Standard	1.715–1.721	43.56–43.71	0.563 (14.30)	0.688 (17.48)	2.031 (51.59)	0.813 (20.65)
SKF 99170	Standard	1.736–1.742	44.09–44.25	0.375 (9.53)	0.500 (12.70)	2.063 (52.40)	0.813 (20.65)
SKF 99172	Standard	1.747–1.753	44.37–44.53	0.375 (9.53)	0.500 (12.70)	2.055 (52.20)	0.813 (20.65)
SKF 99174	Standard	1.747–1.753	44.37–44.53	0.563 (14.30)	0.688 (17.48)	2.063 (52.40)	0.813 (20.65)
SKF 99175	Standard	1.747–1.753	44.37–44.53	0.750 (19.05)	0.875 (22.23)	2.063 (52.40)	0.813 (20.65)
SKF 99180	Standard	1.747–1.753	44.37–44.53	0.531 (13.49)	0.625 (15.88)	2.063 (52.40)	0.878 (22.30)
SKF 99827	Gold	1.747–1.753	44.37–44.53	0.563 (14.30)	0.688 (17.48)	2.063 (52.40)	0.813 (20.65)
SKF 99828	Gold	1.747–1.753	44.37–44.53	0.750 (19.05)	0.875 (22.23)	2.063 (52.40)	0.813 (20.65)
SKF 99176	Standard	1.761–1.767	44.73–44.88	0.563 (14.30)	0.688 (17.48)	2.063 (52.40)	0.813 (20.65)
SKF 99829	Gold	1.761–1.767	44.73–44.88	0.563 (14.30)	0.688 (17.48)	2.063 (52.40)	0.813 (20.65)
SKF 99177	Standard	1.769–1.775	44.93–45.09	0.551 (14.00)	0.669 (16.99)	2.087 (53.01)	0.812 (20.62)
SKF 99830	Gold	1.769–1.775	44.93–45.09	0.551 (14.00)	0.669 (16.99)	2.087 (53.01)	0.812 (20.62)
SKF 99179	Standard	1.778–1.784	45.16–45.31	0.667 (16.94)	0.800 (20.32)	2.125 (53.98)	1.062 (26.97)
SKF 99181	Standard	1.809–1.815	45.95–46.10	0.563 (14.30)	0.688 (17.48)	2.090 (53.09)	1.000 (25.40)
SKF 99831	Gold	1.809–1.815	45.95–46.10	0.563 (14.30)	0.688 (17.48)	2.090 (53.09)	1.000 (25.40)
SKF 99185	Standard	1.857–1.863	47.17–47.32	0.563 (14.30)	0.688 (17.48)	2.156 (54.76)	1.000 (25.40)
SKF 99186	Standard	1.866–1.872	47.40–47.55	0.889 (22.58)	1.025 (26.04)	2.188 (55.58)	1.000 (25.40)
SKF 99184	Standard	1.872–1.878	47.55–47.70	0.375 (9.53)	0.516 (13.11)	2.203 (55.96)	1.050 (26.67)
SKF 99187	Standard	1.872–1.878	47.55–47.70	0.563 (14.30)	0.688 (17.48)	2.203 (55.96)	1.000 (25.40)
SKF 99188	Standard	1.872–1.878	47.55–47.70	0.295 (7.49)	0.415 (10.54)	2.203 (55.96)	0.744 (18.90)
SKF 99190	Standard	1.872–1.878	47.55–47.70	0.175 (4.45)	0.295 (7.49)	2.203 (55.96)	0.744 (18.90)
SKF 99832	Gold	1.872–1.878	47.55–47.70	0.563 (14.30)	0.688 (17.48)	2.203 (55.96)	1.000 (25.40)
SKF 99189	Standard	1.887–1.893	47.93–48.08	0.551 (14.00)	0.668 (16.97)	2.205 (56.01)	0.984 (24.99)
SKF 99192	Standard	1.909–1.915	48.49–48.64	0.375 (9.53)	0.500 (12.70)	2.219 (56.36)	1.000 (25.40)
SKF 99193	Standard	1.934–1.940	49.12–49.28	0.563 (14.30)	0.688 (17.48)	2.219 (56.36)	1.000 (25.40)
SKF 99833	Gold	1.934–1.940	49.12–49.28	0.563 (14.30)	0.688 (17.48)	2.219 (56.36)	1.000 (25.40)
SKF 99052	Standard	1.965–1.971^‡	49.91–50.06^‡	0.551 (14.00)	0.668 (16.97)	2.244 (56.49)	1.350 (34.29)
SKF 99196	Standard	1.965–1.971	49.91–50.06	0.551 (14.00)	0.668 (16.97)	2.244 (57.00)	0.984 (24.99)
SKF 99198	Standard	1.977–1.983	50.22–50.37	0.563 (14.30)	0.704 (17.88)	2.313 (58.75)	1.050 (26.67)

2.000–2.999 in (50.8–76.2 mm) 79 sizes

SKF Speedi-Sleeves for 2.000–2.999 in (50.8–76.2 mm) shafts
Part no.	Type	Fits shaft (in)	Fits shaft (mm)	Covers in (mm)	Total width in (mm)	Flange OD in (mm)	Max install depth in (mm)	Action
SKF 99199	Standard	1.997–2.003	50.72–50.88	0.563 (14.30)	0.688 (17.48)	2.406 (61.11)	1.000 (25.40)
SKF 99200	Standard	1.997–2.003	50.72–50.88	0.875 (22.23)	1.000 (25.40)	2.406 (61.11)	1.000 (25.40)
SKF 99834	Gold	1.997–2.003	50.72–50.88	0.563 (14.30)	0.688 (17.48)	2.406 (61.11)	1.006 (25.55)
SKF 99835	Gold	1.997–2.003	50.72–50.88	0.875 (22.23)	1.000 (25.40)	2.406 (61.11)	1.000 (25.40)
SKF 99878	To confirm	2.040–2.047^†	51.82–51.99^†	0.500 (12.70)	0.625 (15.88)	2.469 (62.71)	1.359 (34.52)
SKF 99205	Standard	2.057–2.063	52.25–52.40	0.781 (19.84)	0.938 (23.83)	2.469 (62.71)	1.375 (34.93)
SKF 99210	Standard	2.123–2.128^†	53.92–54.05^†	0.500 (12.70)	0.750 (19.05)	2.422 (61.52)	1.281 (32.54)
SKF 99212	Standard	2.124–2.130	53.95–54.10	0.781 (19.84)	0.938 (23.83)	2.422 (61.52)	1.375 (34.93)
SKF 99836	Gold	2.124–2.130	53.95–54.10	0.781 (19.84)	0.938 (23.83)	2.422 (61.52)	1.375 (34.93)
SKF 99215	Standard	2.162–2.168	54.91–55.07	0.787 (19.99)	0.905 (22.99)	2.441 (62.00)	1.250 (31.75)
SKF 99863	Gold	2.162–2.168	54.91–55.07	0.787 (19.99)	0.905 (22.99)	2.441 (62.00)	1.250 (31.75)
SKF 99218	Standard	2.186–2.192	55.52–55.68	0.781 (19.84)	0.938 (23.83)	2.500 (63.50)	1.313 (33.35)
SKF 99220	Standard	2.198–2.205^†	55.83–56.01^†	0.500 (12.70)	0.625 (15.88)	2.531 (64.29)	1.313 (33.35)
SKF 99224	Standard	2.198–2.205	55.83–56.01	0.779 (19.79)	0.936 (23.77)	2.531 (64.29)	3.150 (80.01)	Quote
SKF 99229	Standard	2.227–2.233	56.57–56.72	0.500 (12.70)	0.625 (15.88)	2.531 (64.29)	1.313 (33.35)
SKF 99230	Standard	2.227–2.233	56.57–56.72	0.781 (19.84)	0.906 (23.01)	2.531 (64.29)	1.250 (31.75)
SKF 99861	Gold	2.227–2.233	56.57–56.72	0.500 (12.70)	0.625 (15.88)	2.531 (64.29)	1.313 (33.35)	Quote
SKF 99226	Standard	2.237–2.243	56.82–56.97	0.764 (19.41)	0.900 (22.86)	2.563 (65.10)	1.250 (31.75)
SKF 99225	Standard	2.249–2.255	57.12–57.28	0.781 (19.84)	0.938 (23.83)	2.531 (64.29)	1.313 (33.35)
SKF 99227	Standard	2.249–2.255	57.12–57.28	0.313 (7.95)	0.438 (11.13)	2.531 (64.29)	1.313 (33.35)
SKF 99837	Gold	2.249–2.255	57.12–57.28	0.781 (19.84)	0.938 (23.83)	2.531 (64.29)	1.313 (33.35)
SKF 99838	Gold	2.249–2.255	57.12–57.28	0.313 (7.95)	0.438 (11.13)	2.531 (64.29)	1.313 (33.35)
SKF 99219	Standard	2.280–2.286	57.91–58.06	0.787 (19.99)	0.938 (23.83)	2.598 (65.99)	1.375 (34.93)
SKF 99231	Standard	2.309–2.315	58.65–58.80	0.781 (19.84)	0.938 (23.83)	2.688 (68.28)	1.375 (34.93)
SKF 99233	Standard	2.327–2.333	59.11–59.26	0.750 (19.05)	0.875 (22.23)	2.750 (69.85)	1.500 (38.10)
SKF 99235	Standard	2.359–2.365	59.92–60.07	0.787 (19.99)	0.905 (22.99)	2.785 (70.74)	1.375 (34.93)
SKF 99241	Standard	2.359–2.365	59.92–60.07	0.370 (9.40)	0.450 (11.43)	2.785 (70.74)	1.471 (37.36)
SKF 99869	Gold	2.359–2.365	59.92–60.07	0.787 (19.99)	0.905 (22.99)	2.785 (70.74)	1.375 (34.93)
SKF 99238	Standard	2.372–2.378	60.25–60.40	0.594 (15.09)	0.750 (19.05)	2.750 (69.85)	1.375 (34.93)
SKF 99237	Standard	2.374–2.380	60.30–60.45	0.781 (19.84)	0.938 (23.83)	2.750 (69.85)	1.375 (34.93)
SKF 99240	Standard	2.374–2.380	60.30–60.45	0.526 (13.36)	0.683 (17.35)	2.750 (69.85)	1.375 (34.93)
SKF 99839	Gold	2.374–2.380	60.30–60.45	0.781 (19.84)	0.938 (23.83)	2.750 (69.85)	1.375 (34.93)
SKF 99243	Standard	2.434–2.441^†	61.82–62.00^†	0.781 (19.84)	0.938 (23.83)	2.828 (71.83)	1.393 (35.38)
SKF 99244	Standard	2.434–2.441^†	61.82–62.00^†	0.500 (12.70)	0.625 (15.88)	2.828 (71.83)	1.425 (36.20)
SKF 99242	Standard	2.435–2.441	61.85–62.00	0.500 (12.70)	0.625 (15.88)	2.828 (71.83)	1.425 (36.20)
SKF 99249	Standard	2.489–2.495	63.22–63.37	0.781 (19.84)	0.938 (23.83)	2.875 (73.03)	1.393 (35.38)
SKF 99253	Standard	2.497–2.503^†	63.42–63.58^†	0.555 (14.10)	0.650 (16.51)	2.820 (71.63)	0.890 (22.61)
SKF 99248	Standard	2.500–2.506^†	63.50–63.65^†	0.500 (12.70)	0.656 (16.66)	2.828 (71.83)	1.393 (35.38)
SKF 99250	Standard	2.500–2.506^†	63.50–63.65^†	0.781 (19.84)	0.938 (23.83)	2.820 (71.63)	1.375 (34.93)
SKF 99840	Gold	2.500–2.506^†	63.50–63.65^†	0.781 (19.84)	0.938 (23.83)	2.820 (71.63)	1.375 (34.93)
SKF 99251	Standard	2.510–2.516^†	63.75–63.91^†	0.781 (19.84)	0.906 (23.01)	2.828 (71.83)	1.438 (36.53)
SKF 99254	Standard	2.556–2.562^†	64.92–65.07^†	0.787 (19.99)	0.905 (22.99)	2.850 (72.39)	1.375 (34.93)
SKF 99841	Gold	2.556–2.562^†	64.92–65.07^†	0.787 (19.99)	0.905 (22.99)	2.850 (72.39)	1.375 (34.93)
SKF 99256	Standard	2.560–2.566^†	65.02–65.18^†	0.781 (19.84)	0.938 (23.83)	2.891 (73.43)	1.375 (34.93)
SKF 99259	Standard	2.595–2.601^†	65.91–66.07^†	0.781 (19.84)	0.938 (23.83)	2.990 (75.95)	1.250 (31.75)
SKF 99261	Standard	2.618–2.624^†	66.50–66.65^†	0.781 (19.84)	0.938 (23.83)	3.047 (77.39)	1.375 (34.93)
SKF 99264	Standard	2.621–2.627^†	66.57–66.73^†	0.781 (19.84)	0.906 (23.01)	3.047 (77.39)	1.375 (34.93)
SKF 99260	Standard	2.622–2.628^†	66.60–66.75^†	0.500 (12.70)	0.625 (15.88)	3.047 (77.39)	1.375 (34.93)
SKF 99262	Standard	2.625–2.631^†	66.68–66.83^†	0.781 (19.84)	0.938 (23.83)	3.047 (77.39)	1.375 (34.93)
SKF 99842	Gold	2.625–2.631^†	66.68–66.83^†	0.781 (19.84)	0.938 (23.83)	3.047 (77.39)	1.375 (34.93)
SKF 99266	Standard	2.670–2.677	67.82–68.00	0.750 (19.05)	0.875 (22.23)	3.125 (79.38)	1.688 (42.88)
SKF 99268	Standard	2.727–2.733^†	69.27–69.42^†	0.781 (19.84)	0.906 (23.01)	3.125 (79.38)	1.313 (33.35)
SKF 99273	Standard	2.740–2.746^†	69.60–69.75^†	0.781 (19.84)	0.938 (23.83)	3.065 (77.85)	1.250 (31.75)
SKF 99274	Standard	2.745–2.751^†	69.72–69.88^†	0.781 (19.84)	0.938 (23.83)	3.125 (79.38)	1.250 (31.75)
SKF 99843	Gold	2.745–2.751^†	69.72–69.88^†	0.781 (19.84)	0.938 (23.83)	3.125 (79.38)	1.250 (31.75)
SKF 99267	Standard	2.747–2.753^†	69.77–69.93^†	1.438 (36.53)	1.625 (41.28)	3.075 (78.11)	1.625 (41.28)
SKF 99269	Standard	2.750–2.756^†	69.85–70.00^†	1.125 (28.58)	1.250 (31.75)	3.125 (79.38)	1.312 (33.32)
SKF 99272	Standard	2.750–2.756^†	69.85–70.00^†	0.406 (10.31)	0.563 (14.30)	3.125 (79.38)	1.250 (31.75)
SKF 99275	Standard	2.750–2.756^†	69.85–70.00^†	0.781 (19.84)	0.938 (23.83)	3.125 (79.38)	1.250 (31.75)
SKF 99844	Gold	2.750–2.756^†	69.85–70.00^†	0.781 (19.84)	0.938 (23.83)	3.125 (79.38)	1.250 (31.75)
SKF 99276	Standard	2.753–2.759^†	69.93–70.08^†	0.787 (19.99)	0.945 (24.00)	3.125 (79.38)	1.250 (31.75)
SKF 99281	Standard	2.809–2.815^†	71.35–71.50^†	0.594 (15.09)	0.688 (17.48)	3.188 (80.98)	1.250 (31.75)
SKF 99284	Standard	2.828–2.835	71.83–72.01	0.750 (19.05)	0.875 (22.23)	3.225 (81.92)	1.343 (34.11)
SKF 99870	Gold	2.828–2.835	71.83–72.01	0.750 (19.05)	0.875 (22.23)	3.225 (81.92)	1.343 (34.11)
SKF 99282	Standard	2.838–2.844^†	72.09–72.24^†	0.500 (12.70)	0.656 (16.66)	3.225 (81.92)	1.250 (31.75)
SKF 99845	Gold	2.838–2.844^†	72.09–72.24^†	0.500 (12.70)	0.656 (16.66)	3.225 (81.92)	1.250 (31.75)
SKF 99286	Standard	2.866–2.872^†	72.80–72.95^†	0.781 (19.84)	0.938 (23.83)	3.188 (80.98)	1.250 (31.75)
SKF 99287	Standard	2.873–2.879^†	72.97–73.13^†	0.781 (19.84)	0.938 (23.83)	3.219 (81.76)	1.250 (31.75)
SKF 99846	Gold	2.873–2.879^†	72.97–73.13^†	0.781 (19.84)	0.938 (23.83)	3.219 (81.76)	1.250 (31.75)	Quote
SKF 99290	Standard	2.937–2.943^†	74.60–74.75^†	0.500 (12.70)	0.641 (16.28)	3.344 (84.94)	1.331 (33.81)
SKF 99293	Standard	2.937–2.943^†	74.60–74.75^†	0.781 (19.84)	0.938 (23.83)	3.344 (84.94)	1.313 (33.35)
SKF 99847	Gold	2.937–2.943^†	74.60–74.75^†	0.781 (19.84)	0.938 (23.83)	3.344 (84.94)	1.313 (33.35)
SKF 99289	Standard	2.950–2.956^†	74.93–75.08^†	0.594 (15.09)	0.690 (17.53)	3.273 (83.13)	1.083 (27.51)
SKF 99294	Standard	2.950–2.956^†	74.93–75.08^†	0.866 (22.00)	1.024 (26.01)	3.305 (83.95)	1.313 (33.35)
SKF 99875	Gold	2.950–2.956^†	74.93–75.08^†	0.866 (22.00)	1.024 (26.01)	3.305 (83.95)	1.313 (33.35)
SKF 99292	Standard	2.972–2.976^†	75.49–75.59^†	0.813 (20.65)	1.000 (25.40)	3.235 (82.17)	1.250 (31.75)
SKF 99291	Standard	2.990–2.996^†	75.95–76.10^†	0.484 (12.29)	0.625 (15.88)	3.359 (85.32)	1.331 (33.81)
SKF 99298	Standard	2.990–2.996^†	75.95–76.10^†	0.563 (14.30)	0.688 (17.48)	3.359 (85.32)	1.375 (34.93)
SKF 99299	Standard	2.990–2.996^†	75.95–76.10^†	0.813 (20.65)	1.000 (25.40)	3.350 (85.09)	1.281 (32.54)

3.000–3.999 in (76.2–101.6 mm) 58 sizes

SKF Speedi-Sleeves for 3.000–3.999 in (76.2–101.6 mm) shafts
Part no.	Type	Fits shaft (in)	Fits shaft (mm)	Covers in (mm)	Total width in (mm)	Flange OD in (mm)	Max install depth in (mm)	Action
SKF 99296	Standard	2.997–3.003^†	76.12–76.28^†	0.813 (20.65)	0.938 (23.83)	3.240 (82.30)	1.375 (34.93)
SKF 99048	Standard	3.000–3.006^†	76.20–76.35^†	0.625 (15.88)	0.813 (20.65)	3.345 (84.96)	1.280 (32.51)
SKF 99300	Standard	3.000–3.006^†	76.20–76.35^†	0.813 (20.65)	1.000 (25.40)	3.235 (82.17)	1.281 (32.54)
SKF 99848	Gold	3.000–3.006^†	76.20–76.35^†	0.813 (20.65)	1.000 (25.40)	3.235 (82.17)	1.281 (32.54)
SKF 99301	Standard	3.008–3.014^†	76.40–76.56^†	0.500 (12.70)	0.625 (15.88)	3.355 (85.22)	2.000 (50.80)
SKF 99306	Standard	3.064–3.071	77.83–78.00	0.750 (19.05)	0.875 (22.23)	3.468 (88.09)	2.056 (52.22)
SKF 99311	Standard	3.120–3.126^†	79.25–79.40^†	0.688 (17.48)	0.813 (20.65)	3.531 (89.69)	2.000 (50.80)
SKF 99312	Standard	3.120–3.126^†	79.25–79.40^†	0.813 (20.65)	1.000 (25.40)	3.531 (89.69)	2.000 (50.80)
SKF 99849	Gold	3.120–3.126^†	79.25–79.40^†	0.813 (20.65)	1.000 (25.40)	3.531 (89.69)	2.000 (50.80)
SKF 99053	Standard	3.124–3.132^†	79.35–79.55^†	0.551 (14.00)	0.709 (18.01)	3.525 (89.54)	2.031 (51.59)
SKF 99313	Standard	3.142–3.150^†	79.81–80.01^†	0.750 (19.05)	0.886 (22.50)	3.540 (89.92)	1.375 (34.93)
SKF 99315	Standard	3.146–3.153	79.91–80.09	0.827 (21.01)	0.945 (24.00)	3.543 (89.99)	1.375 (34.93)
SKF 99317	Standard	3.146–3.153	79.91–80.09	0.433 (11.00)	0.591 (15.01)	3.543 (89.99)	1.375 (34.93)
SKF 99328	Standard	3.225–3.231^†	81.92–82.07^†	0.660 (16.76)	0.848 (21.54)	3.585 (91.06)	1.750 (44.45)
SKF 99322	Standard	3.247–3.253^†	82.47–82.63^†	0.813 (20.65)	1.000 (25.40)	3.594 (91.29)	1.375 (34.93)
SKF 99324	Standard	3.250–3.256^†	82.55–82.70^†	0.595 (15.11)	0.719 (18.26)	3.575 (90.81)	1.375 (34.93)
SKF 99325	Standard	3.250–3.256^†	82.55–82.70^†	0.813 (20.65)	1.000 (25.40)	3.585 (91.06)	1.375 (34.93)
SKF 99326	Standard	3.250–3.256^†	82.55–82.70^†	0.688 (17.48)	0.875 (22.23)	3.585 (91.06)	1.250 (31.75)
SKF 99850	Gold	3.250–3.256^†	82.55–82.70^†	0.595 (15.11)	0.719 (18.26)	3.575 (90.81)	1.375 (34.93)
SKF 99851	Gold	3.250–3.256^†	82.55–82.70^†	0.813 (20.65)	1.000 (25.40)	3.585 (91.06)	1.375 (34.93)
SKF 99331	Standard	3.307–3.313^†	84.00–84.15^†	0.813 (20.65)	1.000 (25.40)	3.688 (93.68)	1.375 (34.93)
SKF 99332	Standard	3.337–3.347^†	84.76–85.01^†	0.669 (16.99)	0.827 (21.01)	3.700 (93.98)	1.378 (35.00)
SKF 99333	Standard	3.337–3.347^†	84.76–85.01^†	0.827 (21.01)	0.984 (24.99)	3.700 (93.98)	1.378 (35.00)
SKF 99872	Gold	3.337–3.347^†	84.76–85.01^†	0.827 (21.01)	0.984 (24.99)	3.700 (93.98)	1.378 (35.00)
SKF 99334	Standard	3.338–3.347^†	84.79–85.01^†	0.399 (10.13)	0.499 (12.67)	3.580 (90.93)	1.431 (36.35)
SKF 99337	Standard	3.373–3.379^†	85.67–85.83^†	0.813 (20.65)	1.000 (25.40)	3.695 (93.85)	1.375 (34.93)
SKF 99338	Standard	3.373–3.379^†	85.67–85.83^†	0.375 (9.53)	0.500 (12.70)	3.688 (93.68)	1.410 (35.81)
SKF 99339	Standard	3.435–3.441^†	87.25–87.40^†	0.781 (19.84)	0.906 (23.01)	3.844 (97.64)	1.406 (35.71)
SKF 99481	Standard	3.457–3.465^†	87.80–88.00^†	1.150 (29.21)	1.349 (34.27)	3.751 (95.28)	1.673 (42.50)	Quote
SKF 99340	Standard	3.477–3.483^†	88.32–88.47^†	0.781 (19.84)	0.906 (23.01)	3.835 (97.41)	1.406 (35.71)
SKF 99346	Standard	3.497–3.503^†	88.82–88.98^†	0.625 (15.88)	0.813 (20.65)	3.844 (97.64)	1.347 (34.21)
SKF 99347	Standard	3.500–3.506^†	88.90–89.05^†	0.313 (7.95)	0.500 (12.70)	3.825 (97.16)	1.347 (34.21)
SKF 99350	Standard	3.500–3.506^†	88.90–89.05^†	0.813 (20.65)	1.000 (25.40)	3.844 (97.64)	1.347 (34.21)
SKF 99852	Gold	3.500–3.506^†	88.90–89.05^†	0.813 (20.65)	1.000 (25.40)	3.844 (97.64)	1.347 (34.21)
SKF 99349	Standard	3.501–3.507^†	88.93–89.08^†	0.625 (15.88)	0.813 (20.65)	3.844 (97.64)	1.348 (34.24)
SKF 99351	Standard	3.540–3.546^†	89.92–90.07^†	0.710 (18.03)	0.906 (23.01)	4.000 (101.60)	1.813 (46.05)
SKF 99352	Standard	3.540–3.546^†	89.92–90.07^†	0.438 (11.13)	0.538 (13.67)	4.000 (101.60)	1.813 (46.05)
SKF 99353	Standard	3.540–3.546^†	89.92–90.07^†	0.526 (13.36)	0.667 (16.94)	4.000 (101.60)	1.750 (44.45)
SKF 99354	Standard	3.540–3.546^†	89.92–90.07^†	0.906 (23.01)	1.102 (27.99)	4.000 (101.60)	1.750 (44.45)
SKF 99356	Standard	3.560–3.566^†	90.42–90.58^†	0.813 (20.65)	1.000 (25.40)	3.900 (99.06)	1.750 (44.45)
SKF 99360	Standard	3.618–3.624^†	91.90–92.05^†	0.813 (20.65)	1.000 (25.40)	4.031 (102.39)	1.750 (44.45)
SKF 99362	Standard	3.623–3.629^†	92.02–92.18^†	0.813 (20.65)	1.000 (25.40)	4.031 (102.39)	1.750 (44.45)
SKF 99363	Standard	3.623–3.629^†	92.02–92.18^†	0.500 (12.70)	0.625 (15.88)	4.025 (102.24)	1.750 (44.45)
SKF 99368	Standard	3.684–3.690^†	93.57–93.73^†	0.313 (7.95)	0.438 (11.13)	4.031 (102.39)	0.875 (22.23)
SKF 99365	Standard	3.685–3.691^†	93.60–93.75^†	0.813 (20.65)	0.938 (23.83)	4.025 (102.24)	1.800 (45.72)
SKF 99359	Standard	3.727–3.733^†	94.67–94.82^†	0.469 (11.91)	0.594 (15.09)	4.016 (102.01)	1.800 (45.72)
SKF 99366	Standard	3.727–3.733^†	94.67–94.82^†	0.781 (19.84)	0.906 (23.01)	4.025 (102.24)	1.800 (45.72)
SKF 99369	Standard	3.737–3.743^†	94.92–95.07^†	0.827 (21.01)	0.945 (24.00)	4.025 (102.24)	1.800 (45.72)
SKF 99364	Standard	3.740–3.746^†	95.00–95.15^†	0.469 (11.91)	0.594 (15.09)	4.035 (102.49)	1.800 (45.72)
SKF 99374	Standard	3.740–3.746^†	95.00–95.15^†	0.344 (8.74)	0.500 (12.70)	4.031 (102.39)	1.800 (45.72)
SKF 99376	Standard	3.746–3.752^†	95.15–95.30^†	0.563 (14.30)	0.688 (17.48)	4.025 (102.24)	1.800 (45.72)
SKF 99367	Standard	3.750–3.756^†	95.25–95.40^†	0.344 (8.74)	0.500 (12.70)	4.025 (102.24)	1.800 (45.72)
SKF 99372	Standard	3.750–3.756^†	95.25–95.40^†	0.688 (17.48)	0.875 (22.23)	4.020 (102.11)	1.800 (45.72)
SKF 99853	Gold	3.750–3.756^†	95.25–95.40^†	0.688 (17.48)	0.875 (22.23)	4.020 (102.11)	1.800 (45.72)
SKF 99386	Standard	3.868–3.874^†	98.25–98.40^†	0.813 (20.65)	1.000 (25.40)	4.185 (106.30)	1.875 (47.63)
SKF 99387	Standard	3.873–3.879^†	98.37–98.53^†	0.813 (20.65)	1.000 (25.40)	4.219 (107.16)	1.875 (47.63)
SKF 99393	Standard	3.935–3.941^†	99.95–100.10^†	0.813 (20.65)	1.000 (25.40)	4.313 (109.55)	2.050 (52.07)
SKF 99854	Gold	3.935–3.941^†	99.95–100.10^†	0.813 (20.65)	1.000 (25.40)	4.313 (109.55)	2.050 (52.07)

4.000–4.999 in (101.6–127 mm) 30 sizes

SKF Speedi-Sleeves for 4.000–4.999 in (101.6–127 mm) shafts
Part no.	Type	Fits shaft (in)	Fits shaft (mm)	Covers in (mm)	Total width in (mm)	Flange OD in (mm)	Max install depth in (mm)	Action
SKF 99395	Standard	3.998–4.006	101.55–101.75	0.600 (15.24)	0.725 (18.42)	4.375 (111.13)	2.050 (52.07)
SKF 99399	Standard	3.998–4.006	101.55–101.75	0.813 (20.65)	1.000 (25.40)	4.375 (111.13)	2.050 (52.07)
SKF 99400	Standard	3.998–4.006	101.55–101.75	0.650 (16.51)	0.775 (19.69)	4.375 (111.13)	1.375 (34.93)
SKF 99401	Standard	3.998–4.006	101.55–101.75	0.500 (12.70)	0.625 (15.88)	4.375 (111.13)	2.066 (52.48)
SKF 99855	Gold	3.998–4.006	101.55–101.75	0.813 (20.65)	1.000 (25.40)	4.375 (111.13)	2.050 (52.07)
SKF 99409	Standard	4.090–4.098	103.89–104.09	0.787 (19.99)	0.945 (24.00)	4.438 (112.73)	1.417 (35.99)
SKF 99412	Standard	4.122–4.130	104.70–104.90	0.813 (20.65)	1.000 (25.40)	4.470 (113.54)	1.375 (34.93)
SKF 99413	Standard	4.130–4.138	104.90–105.11	0.787 (19.99)	0.913 (23.19)	4.470 (113.54)	1.378 (35.00)
SKF 99418	Standard	4.183–4.191	106.25–106.45	0.813 (20.65)	1.000 (25.40)	4.500 (114.30)	1.375 (34.93)
SKF 99423	Standard	4.226–4.234	107.34–107.54	0.781 (19.84)	0.906 (23.01)	4.610 (117.09)	1.438 (36.53)
SKF 99424	Standard	4.248–4.256	107.90–108.10	0.813 (20.65)	1.000 (25.40)	4.610 (117.09)	1.438 (36.53)
SKF 99434	Standard	4.322–4.331^†	109.78–110.01^†	0.448 (11.38)	0.589 (14.96)	4.921 (124.99)	1.297 (32.94)
SKF 99435	Standard	4.327–4.335	109.91–110.11	0.509 (12.93)	0.650 (16.51)	4.921 (124.99)	1.250 (31.75)
SKF 99437	Standard	4.370–4.378	111.00–111.20	0.813 (20.65)	1.000 (25.40)	4.750 (120.65)	1.650 (41.91)
SKF 99438	Standard	4.401–4.409	111.79–111.99	0.750 (19.05)	0.886 (22.50)	4.750 (120.65)	1.300 (33.02)
SKF 99439	Standard	4.434–4.442	112.62–112.83	1.000 (25.40)	1.142 (29.01)	4.813 (122.25)	1.313 (33.35)
SKF 99450	Standard	4.496–4.504	114.20–114.40	0.813 (20.65)	1.000 (25.40)	4.900 (124.46)	1.250 (31.75)
SKF 99856	Gold	4.496–4.504	114.20–114.40	0.813 (20.65)	1.000 (25.40)	4.850 (123.19)	1.250 (31.75)
SKF 99452	Standard	4.523–4.531	114.88–115.09	0.813 (20.65)	0.938 (23.83)	5.000 (127.00)	1.250 (31.75)
SKF 99463	Standard	4.621–4.629	117.37–117.58	1.000 (25.40)	1.250 (31.75)	5.063 (128.60)	1.375 (34.93)
SKF 99465	Standard	4.621–4.629	117.37–117.58	0.438 (11.13)	0.625 (15.88)	5.000 (127.00)	1.375 (34.93)
SKF 99468	Standard	4.685–4.693	119.00–119.20	0.813 (20.65)	1.000 (25.40)	5.063 (128.60)	1.375 (34.93)
SKF 99471	Standard	4.720–4.728	119.89–120.09	0.315 (8.00)	0.433 (11.00)	5.110 (129.79)	1.323 (33.60)
SKF 99473	Standard	4.720–4.728	119.89–120.09	0.787 (19.99)	0.984 (24.99)	5.110 (129.79)	1.260 (32.00)
SKF 99475	Standard	4.746–4.754	120.55–120.75	0.500 (12.70)	0.750 (19.05)	5.000 (127.00)	1.500 (38.10)
SKF 99472	Standard	4.799–4.807	121.89–122.10	0.787 (19.99)	0.945 (24.00)	5.177 (131.50)	1.260 (32.00)
SKF 99484	Standard	4.839–4.847^‡	122.91–123.11^‡	0.787 (19.99)	0.984 (24.99)	5.229 (132.82)	1.244 (31.60)	Quote
SKF 99487	Standard	4.871–4.879	123.72–123.93	0.625 (15.88)	0.750 (19.05)	5.250 (133.35)	1.438 (36.53)
SKF 99490	Standard	4.917–4.925	124.89–125.10	0.394 (10.01)	0.551 (14.00)	5.400 (137.16)	1.438 (36.53)
SKF 99492	Standard	4.917–4.925	124.89–125.10	1.024 (26.01)	1.260 (32.00)	5.400 (137.16)	1.438 (36.53)

5.000–5.999 in (127–152.4 mm) 27 sizes

SKF Speedi-Sleeves for 5.000–5.999 in (127–152.4 mm) shafts
Part no.	Type	Fits shaft (in)	Fits shaft (mm)	Covers in (mm)	Total width in (mm)	Flange OD in (mm)	Max install depth in (mm)	Action
SKF 99498	Standard	4.998–5.006^†	126.95–127.15^†	0.688 (17.48)	0.875 (22.23)	5.400 (137.16)	1.438 (36.53)
SKF 99499	Standard	4.998–5.006^†	126.95–127.15^†	0.813 (20.65)	1.000 (25.40)	5.390 (136.91)	1.438 (36.53)
SKF 99501	Standard	4.998–5.006^†	126.95–127.15^†	0.540 (13.72)	0.681 (17.30)	5.400 (137.16)	1.438 (36.53)
SKF 99857	Gold	4.998–5.006^†	126.95–127.15^†	0.688 (17.48)	0.875 (22.23)	5.400 (137.16)	1.438 (36.53)	Quote
SKF 99858	Gold	4.998–5.006^†	126.95–127.15^†	0.813 (20.65)	1.000 (25.40)	5.390 (136.91)	1.438 (36.53)
SKF 99482	Standard	5.032–5.039^†	127.80–128.00^†	1.150 (29.21)	1.349 (34.27)	5.325 (135.26)	1.587 (40.30)	Quote
SKF 99494	Standard	5.110–5.118^†	129.79–130.00^†	0.750 (19.05)	0.938 (23.83)	5.493 (139.52)	1.181 (30.00)
SKF 99491	Standard	5.117–5.125^†	129.97–130.18^†	0.866 (22.00)	0.996 (25.30)	5.493 (139.52)	1.280 (32.51)
SKF 99874	Gold	5.117–5.125^‡	129.97–130.18^‡	0.866 (22.00)	0.996 (25.30)	5.493 (139.52)	1.280 (32.51)	Quote
SKF 99513	Standard	5.120–5.128^†	130.05–130.25^†	0.813 (20.65)	1.000 (25.40)	5.500 (139.70)	1.250 (31.75)
SKF 99525	Standard	5.246–5.254^†	133.25–133.45^†	0.813 (20.65)	1.000 (25.40)	5.560 (141.22)	1.250 (31.75)
SKF 99533	Standard	5.307–5.315^†	134.80–135.00^†	0.807 (20.50)	1.000 (25.40)	5.735 (145.67)	1.250 (31.75)
SKF 99537	Standard	5.371–5.379^†	136.42–136.63^†	0.813 (20.65)	1.000 (25.40)	5.875 (149.23)	1.250 (31.75)
SKF 99548	Standard	5.434–5.442^†	138.02–138.23^†	1.500 (38.10)	1.688 (42.88)	5.750 (146.05)	1.875 (47.63)	Quote
SKF 99547	Standard	5.472–5.480^†	138.99–139.19^†	0.563 (14.30)	0.750 (19.05)	5.900 (149.86)	1.234 (31.34)
SKF 99549	Standard	5.498–5.506^†	139.65–139.85^†	0.813 (20.65)	1.000 (25.40)	5.938 (150.83)	1.250 (31.75)
SKF 99550	Standard	5.498–5.506^†	139.65–139.85^†	0.518 (13.16)	0.705 (17.91)	5.938 (150.83)	1.250 (31.75)
SKF 99859	Gold	5.498–5.506^†	139.65–139.85^†	0.813 (20.65)	1.000 (25.40)	5.938 (150.83)	1.250 (31.75)
SKF 99552	Standard	5.508–5.516^†	139.90–140.11^†	0.807 (20.50)	1.000 (25.40)	5.945 (151.00)	1.250 (31.75)
SKF 99560	Standard	5.621–5.629^†	142.77–142.98^†	0.875 (22.23)	1.000 (25.40)	6.188 (157.18)	1.812 (46.02)
SKF 99571	Standard	5.699–5.709^†	144.75–145.01^†	0.750 (19.05)	0.875 (22.23)	6.100 (154.94)	1.812 (46.02)
SKF 99562	Standard	5.726–5.734^†	145.44–145.64^†	0.563 (14.30)	0.750 (19.05)	6.100 (154.94)	1.938 (49.23)
SKF 99575	Standard	5.746–5.754^†	145.95–146.15^†	0.813 (20.65)	1.000 (25.40)	6.180 (156.97)	1.750 (44.45)
SKF 99587	Standard	5.871–5.879^†	149.12–149.33^†	1.000 (25.40)	1.250 (31.75)	6.188 (157.18)	1.313 (33.35)
SKF 99862	Gold	5.871–5.879^†	149.12–149.33^†	1.000 (25.40)	1.250 (31.75)	6.188 (157.18)	1.313 (33.35)	Quote
SKF 99595	Standard	5.896–5.906^†	149.76–150.01^†	1.024 (26.01)	1.181 (30.00)	6.260 (159.00)	1.280 (32.51)
SKF 99596	Standard	5.934–5.942^†	150.72–150.93^†	1.000 (25.40)	1.125 (28.58)	6.375 (161.93)	1.875 (47.63)

6.000–8.010 in (152.4–203.5 mm) 22 sizes

SKF Speedi-Sleeves for 6.000–8.010 in (152.4–203.5 mm) shafts
Part no.	Type	Fits shaft (in)	Fits shaft (mm)	Covers in (mm)	Total width in (mm)	Flange OD in (mm)	Max install depth in (mm)	Action
SKF 99599	Standard	5.995–6.003^†	152.27–152.48^†	1.000 (25.40)	1.250 (31.75)	6.375 (161.93)	1.750 (44.45)
SKF 99601	Standard	5.995–6.003^‡	152.27–152.48^‡	0.500 (12.70)	0.750 (19.05)	6.360 (161.54)	1.750 (44.45)
SKF 99605	Standard	6.058–6.068	153.87–154.13	1.024 (26.01)	1.181 (30.00)	6.375 (161.93)	1.299 (32.99)
SKF 99606	Standard	6.092–6.102	154.74–154.99	1.024 (26.01)	1.181 (30.00)	6.575 (167.01)	1.299 (32.99)
SKF 99620	Standard	6.198–6.208	157.43–157.68	0.813 (20.65)	1.063 (27.00)	6.625 (168.28)	1.750 (44.45)
SKF 99625	Standard	6.245–6.255	158.62–158.88	1.031 (26.19)	1.250 (31.75)	6.625 (168.28)	1.750 (44.45)
SKF 99630	Standard	6.289–6.299	159.74–159.99	1.000 (25.40)	1.250 (31.75)	6.750 (171.45)	1.375 (34.93)
SKF 99650	Standard	6.495–6.505	164.97–165.23	1.000 (25.40)	1.250 (31.75)	7.000 (177.80)	1.375 (34.93)
SKF 99640	Standard	6.683–6.693	169.75–170.00	1.250 (31.75)	1.496 (38.00)	7.188 (182.58)	1.750 (44.45)
SKF 99675	Standard	6.745–6.755	171.32–171.58	0.813 (20.65)	1.063 (27.00)	7.125 (180.98)	1.750 (44.45)
SKF 99687	Standard	6.880–6.890	174.75–175.01	1.102 (27.99)	1.260 (32.00)	7.362 (186.99)	1.378 (35.00)
SKF 99700	Standard	6.995–7.005^†	177.67–177.93^†	1.000 (25.40)	1.250 (31.75)	7.475 (189.87)	1.688 (42.88)
SKF 99864	Gold	6.995–7.005^‡	177.67–177.93^‡	1.000 (25.40)	1.250 (31.75)	7.475 (189.87)	1.688 (42.88)	Quote
SKF 99721	Standard	7.077–7.087^†	179.76–180.01^†	1.299 (32.99)	1.496 (38.00)	7.500 (190.50)	1.752 (44.50)
SKF 99725	Standard	7.244–7.254^†	184.00–184.25^†	1.250 (31.75)	1.500 (38.10)	7.760 (197.10)	2.175 (55.25)
SKF 99726	Standard	7.273–7.283^†	184.73–184.99^†	1.260 (32.00)	1.496 (38.00)	7.760 (197.10)	2.165 (54.99)
SKF 99745	Standard	7.444–7.454^†	189.08–189.33^†	0.813 (20.65)	1.000 (25.40)	7.860 (199.64)	1.250 (31.75)
SKF 99750	Standard	7.495–7.505^†	190.37–190.63^†	0.813 (20.65)	1.000 (25.40)	7.875 (200.03)	1.250 (31.75)
SKF 99775	Standard	7.745–7.755^†	196.72–196.98^†	1.000 (25.40)	1.313 (33.35)	8.270 (210.06)	1.875 (47.63)	Quote
SKF 99787	Standard	7.869–7.879^†	199.87–200.13^†	1.359 (34.52)	1.500 (38.10)	8.375 (212.73)	1.750 (44.45)
SKF 99799	Standard	7.933–7.943^†	201.50–201.75^†	1.000 (25.40)	1.250 (31.75)	8.375 (212.73)	1.750 (44.45)	Quote
SKF 99800	Standard	7.995–8.005^†	203.07–203.33^†	1.000 (25.40)	1.250 (31.75)	8.375 (212.73)	1.750 (44.45)

How to read the chart

Size bands: Sizes are grouped by shaft diameter. A size whose range spans a whole inch, such as 0.998–1.002 in, is listed with that inch (here, 1–2 in).
Fits shaft: The shaft diameter range the sleeve is made for. The average of your readings must fall inside it.
Covers: Width on the shaft: the sealing surface the sleeve gives you. It must cover the whole worn band.
Total width: The full width, including the removable flange.
Flange OD: The outside diameter of the flange.
Max install depth: How far along the shaft the included tool can fit the sleeve. Further in, use a pipe (see Installation).
Type: Standard (plain stainless-steel surface) or Gold (the same stainless steel with a thin, harder-wearing coating for abrasive or dirty duty). “To confirm” means SKF's sources disagree on the type: ask us.
† Editions differ: SKF's catalogue editions give slightly different ranges for this part. If your reading is near either end, confirm with us.
‡ One edition only: Listed in one SKF catalogue edition only. Confirm with us before you order.

Sizes from SKF Industrial shaft seals catalogue (2021), with the 2024 CR Seals handbook as a secondary source. Parts marked Quote aren't listed online yet: we can order them for you. SKF® and Speedi-Sleeve® are registered trademarks of the SKF Group.

Installation guide

How to install an SKF Speedi-Sleeve

Fitting a Speedi-Sleeve takes a few minutes and no machining. You need the installation tool that comes in the box, a hammer or mallet, and long-nosed pliers if the flange has to come off. Read every step before you start: once a sleeve is on, it can't be taken off and used again.

Flange end on first, the tool from the box over the sleeve, then tap the centre of the tool until the sleeve covers the worn band.

Warning

Never heat a Speedi-Sleeve. A heated sleeve may not shrink back and would be loose on the shaft. It is made to be pressed on cold with the tool in the box. Heat is only used on the much thicker LDSLV sleeves for shafts over 8.313 in.

Clean and deburr the shaft
Clean the sealing area and file off any burrs, nicks or rough spots. Check once more that there's no keyway, spline, cross hole or thread where the sleeve will sit.
Mark where the sleeve goes
Using the distances you noted when measuring, mark the position on the shaft so the sleeve will cover the whole worn band, including the dust-lip track.
Fill the groove if you need to
Light wear: no filler is needed. If you like, put a thin coat of non-hardening sealant in the bore of the sleeve.
Deep grooves or scoring: fill them with a powdered-metal epoxy filler and install the sleeve before the filler cures.
Notch the flange now if it has to come off
The flange can usually stay on. If it would press against the new seal, hit a part that stays on the shaft, or block oil from reaching the seal, it must come off after fitting. Cut a notch from its outer edge into the radius now, before the sleeve goes on.
Start the sleeve flange end first
Slide the sleeve onto the shaft with the flange end leading, so the flange ends up on the inboard side. Then place the installation tool from the box over the sleeve.
Tap it into position
Tap the centre of the tool squarely with a hammer or mallet until the sleeve covers the marked band. If the tool is too short to reach, use a length of pipe with the same inside diameter as the tool and a square, burr-free end. Never heat the sleeve to help it on.
Check the outer edge
The outer edge of the sleeve must sit on the full shaft diameter, not on the chamfer or lead-in, where its sharp edge could cut the new seal. Then look the shaft over again for any burr that could damage the seal, and take care not to scratch the sleeve's smooth outer surface.
Remove the flange if needed
If you notched the flange, grip it at the notch with long-nosed pliers and coil it off around the shaft. Don't lift the end of the sleeve as you go.
Clean, lubricate and fit a new seal
Wipe any sealant or filler off the sleeve surface, then lubricate it with the oil or grease the seal will run in. The sleeve wall is only 0.011 in (0.28 mm), so there's no size change: fit a new seal of the original size.

Questions & answers

Speedi-Sleeve FAQ

Quick answers to what customers ask us most. Still not sure? Send us your readings and we'll pick the part for you.

What is an SKF Speedi-Sleeve?

A Speedi-Sleeve is a thin stainless-steel sleeve that presses onto a worn shaft and gives the seal a new, smooth running surface. It repairs the groove a seal lip wears into a shaft without machining, welding or replacing the shaft, and it fits in a few minutes. See every size in our SKF Speedi-Sleeve collection.

Do I need a different seal size with a Speedi-Sleeve?

No. The sleeve wall is only 0.011 in (0.28 mm) thick, so the seal size you already use still fits. Always fit a new seal, though: the old lip has worn to match the old groove. Shop seals of the original size.

How do I measure my shaft for a Speedi-Sleeve?

Clean the shaft, then use a micrometer on the smooth, unworn part right next to the worn band, where the sleeve will sit. Take three readings about 60° apart and average them. Enter the readings in the size finder, or follow the full steps in How to measure.

My shaft is between two sizes. What should I do?

Measure again with a micrometer at three points and use the average. If it still falls between two ranges in the size chart, or right at the edge of one, don't guess: a sleeve that's too loose or too tight won't seal. Send us your readings from the finder and we'll confirm the right part.

Which Speedi-Sleeve width do I need?

Choose a sleeve whose width on the shaft (the Covers column in the chart) covers the whole worn band, including the dust-lip track and any end float. Many shaft sizes come in more than one width: at 2.000 in, for example, SKF 99199 covers 0.563 in and SKF 99200 covers 0.875 in. Enter where the band starts and ends in the size finder and it checks the width for you.

What's the difference between Standard and Gold Speedi-Sleeves?

Both fit the same shaft ranges and install the same way. Standard sleeves have a plain stainless-steel surface and suit most jobs. Gold sleeves add a thin, harder-wearing coating to the same stainless steel, for abrasive or dirty duty such as grit, mud or dust. Where SKF makes both for your size, the chart and the finder list both.

Do I have to remove the flange?

Usually not. Remove it only if it would press against the new seal's back face or a part that stays on the shaft, or block oil from reaching the seal. If it has to come off, notch it before you install the sleeve, then coil it off with long-nosed pliers afterwards without lifting the end of the sleeve. See the installation steps.

Can I fit a Speedi-Sleeve over a keyway, or heat it to get it on?

No to both. A Speedi-Sleeve can't go over a keyway, spline, cross hole or thread. And never heat a Speedi-Sleeve: it may not shrink back and would be loose on the shaft. It is made to be tapped on cold with the installation tool.

My shaft is over 8 in. Is there a sleeve for it?

Speedi-Sleeves go up to 8 in (203 mm). For shafts from 8.313 in to 45 in (211 to 1,143 mm), SKF makes the LDSLV heavy-duty wear sleeve to order. Its wall is 0.094 in (2.39 mm) thick and it is heated to fit, so you either fit a seal sized for a shaft 0.188 in (4.78 mm) larger, or machine the shaft down 0.188 in and keep the original seal size. Ask us for an LDSLV quote.

Is the installation tool included, and can a sleeve be reused?

Yes, every SKF Speedi-Sleeve comes with its own installation tool in the box. You'll also need a hammer or mallet, and long-nosed pliers if the flange has to come off. A sleeve can't be reused: once it's on the shaft, it can't be taken off and fitted again, so check your readings before you install.

Speedi Sleeve Size Chart

Find your SKF Speedi-Sleeve

Request a quote

How to measure your shaft for a Speedi-Sleeve

Clean the shaft

Find the unworn section next to the worn band

Take three readings with a micrometer

Average the readings

Note where the worn band starts and ends

Check for anything in the way

SKF Speedi-Sleeve size chart

How to read the chart

How to install an SKF Speedi-Sleeve

Clean and deburr the shaft

Mark where the sleeve goes

Fill the groove if you need to

Notch the flange now if it has to come off

Start the sleeve flange end first

Tap it into position

Check the outer edge

Remove the flange if needed

Clean, lubricate and fit a new seal